BOOK · LESSON 9

第 9 课：Fusion 入门L9: An Introduction to Fusion

按教材子目录切分的跟练卡：每张卡一页，跟着步骤做项目。One card per book section, each on its own page.

9 sections

  1. 视觉特效合成概述An Introduction to Visual Effects Compositing
  2. 创建 Fusion 合成Creating a Fusion Composition9 steps
  3. 添加第一个节点Adding the First Node9 steps
  4. Merge 节点The Merge Node9 steps
    TASK 1Task 1连接合并节点Connect Merge NodeTASK 2Task 2视图导航操作Viewer Navigation
  5. 文字创建Text Creation10 steps
  6. 关键帧与动画Keyframes and Animation30 steps
    TASK 1Task 1位移关键帧Position KeyframesTASK 2Task 2手写动画Write-On Animation
  7. 在剪辑页面快速变换Quick Changes in the Edit Page8 steps
  8. 设置合成节点Setting Up Composite Nodes14 steps
  9. 添加模糊蒙版Add Blur and Mask18 steps

单元任务Unit Brief

你的任务

挑一个自己拍的镜头（或教材配套工程里的片段），进 Fusion 页面给它叠一段动态标题：用 Text+ 写字、Merge 叠加、Transform 挪位，再用关键帧和样条线让标题缓进缓出地进场，最后导出一帧成品画面。

素材要求

  • 任意一个 5 秒以上的镜头，自备拍摄或用教材配套工程的片段都行——画面里最好有一块相对干净的空白区，给标题留位置
  • 不需要绿幕或特效素材，这是一次"画面 + 文字"的最小合成

步骤提示

  1. 在剪辑页把镜头放上时间线，切到 Fusion 页面，确认 MediaIn 和 MediaOut 已经等在节点区
  2. 选中 MediaIn 加 Text+（Merge 自动跟上），打好标题文字，再挂 Transform 把它挪到画面合适的位置
  3. 给 Text+ 或 Transform 的参数打关键帧做出进场动画，打开样条线编辑器把匀速动作调成缓入缓出
  4. 回剪辑页播放检查，导出一帧成品图和一段带标题的视频

自评标准

Your task

Pick one of your own shots (or a clip from the companion project), head to the Fusion page, and layer a motion title over it: write it with Text+, composite it with a Merge, place it with a Transform, then use keyframes and the Spline Editor to ease the title in — and export one finished frame at the end.

Footage

  • Any shot longer than 5 seconds — your own footage or a clip from the companion project. Prefer a frame with a relatively clean, empty area where the title can sit.
  • No green screen or VFX plates needed; this is a minimal "footage + text" composite.

Suggested steps

  1. Place the shot on the timeline on the Edit page, then switch to the Fusion page and confirm MediaIn and MediaOut are waiting in the node area.
  2. Select MediaIn and add a Text+ (a Merge comes along automatically), type your title, then hang a Transform to place it in the frame.
  3. Keyframe the Text+ or Transform parameters for an entrance, then open the Spline Editor and turn the constant-speed move into an eased one.
  4. Check playback on the Edit page, then export one finished frame and a clip with the title.

Self-check

本课自测Lesson Quiz