检查器音量控制Inspector Volume Control

难度LEVELL1 · 入门L1 · Beginner 领域TOPIC音频

先学：Prerequisites: 时间线

学习目标LEARNING OBJECTIVES

学完你能用检查器（Inspector）里的 Volume 参数精确调整片段音量，并看懂 dB 数值的含义。

概念说明CONCEPTS

检查器音量控制（Inspector Volume Control）是检查器 Audio 选项卡里的 Volume 参数——它以 dB 为单位调整选中片段的增益，是调音量最精确的方式。

  • 0 dB 是原始电平：数值表示相对源片段录音电平的增减量，不是绝对响度。
  • 负降正升：负值让片段变轻，正值变响；对话峰值常以 -9 dBFS 上下为起点。
  • 可边播边调：回放中拖动或输入即可实时听到变化，方便对照混音找位置。
  • 与增益线同步：这里改的数值和时间线上的片段增益线是同一处调整，两边联动（见 片段增益线）。

操作步骤STEPS

  1. 在时间线选中要调整的音频片段
  2. 点击界面右上角的 Inspector 打开检查器
  3. 切换到 Audio 选项卡，找到 Volume 参数检查器 Audio 选项卡里的 Volume
  4. 直接输入数值（如 -3）或拖动滑杆，边听边调
  5. 想恢复时双击数值，重置回 0 dB

练习PRACTICE

  1. 选中一段对话片段，把 Volume 依次设为 -3、-6、0 dB，回放对比响度差别。
  2. 把一段音乐片段降 -10 dB，再用双击重置回 0 dB。

常见问题FAQ

Volume 显示 -3 dB 是什么意思？

表示在片段原始录音电平的基础上降了 3 dB。它记录的是增减量，不是片段的实际响度——实际电平看混音器（Mixer）的电平表。

在检查器调的音量，导出时会生效吗？

会。它直接改变片段的输出电平，导出结果与回放一致；它和时间线增益线是同一处调整。

调乱了想回到原始音量怎么办？

双击 Volume 数值或滑杆即重置为 0 dB，片段恢复原始录音电平。

Learning Objectives学习目标

After this card you can adjust a clip's volume precisely with the Volume parameter in the Inspector, and read what the dB value means.

Concepts概念说明

Inspector Volume Control is the Volume parameter on the Inspector's Audio tab — it adjusts the selected clip's gain in dB, and it's the most precise way to set volume.

  • 0 dB is the original level: the value is the change relative to the source recording, not an absolute loudness.
  • Negative down, positive up: negative values make the clip quieter, positive louder; dialogue peaks often start around -9 dBFS.
  • Adjust while playing: drag or type during playback and hear the change in real time.
  • Synced with the gain line: this and the timeline clip gain line are the same adjustment — move one and the other follows (see Clip Gain Line).

Steps操作步骤

  1. Select the audio clip in the timeline
  2. Click Inspector at the top right of the interface
  3. Switch to the Audio tab and find the Volume parameterVolume on the Inspector's Audio tab
  4. Type a value (e.g. -3) or drag the slider, listening as you go
  5. To restore, double-click the value to reset to 0 dB

Practice练习

  1. Select a dialogue clip, set Volume to -3, -6, then 0 dB, and play back to compare loudness.
  2. Drop a music clip by -10 dB, then double-click to reset it to 0 dB.

FAQ常见问题

What does -3 dB in Volume mean?

The clip plays 3 dB below its original recorded level. It's a relative change, not absolute loudness — watch the Mixer meters for actual levels.

Will my Inspector volume change carry into the export?

Yes. It changes the clip's actual output level, so the export matches playback — it's the same adjustment as the timeline gain line.

I messed it up — how do I get back to the original volume?

Double-click the Volume value or slider to reset to 0 dB, restoring the clip's original recorded level.

深度资料：检查器音量控制 →Deep dive: 检查器音量控制 →

本卡术语Terms in this card

时间线Timeline 导出Export 响度Loudness 检查器Inspector 调音台Mixer Gain（亮部）Gain